Congrats on the new company.....and the progress displayed here.....best of luck with the future........
|
Quote:
|
Put me down for two to start. Will then hopefully work up to a squad. Add a pair of 45 inch battlestars to.
Jim :salute: :thumbsup: |
Quote:
|
As for everyone wishing for update pics, we are ironing out any detail problems and should have pics of casted pieces withing a day or so. Pre-orders will be then accepted following to get the real kit castings rolling into reality. :salute:
|
Here are master build up pics. Before molding. Canopy master as well as vertical stabilizer and left wing, showing panel lines and intake details. :salute:
http://tinypic.com/hv5p9y.jpg http://tinypic.com/hv5pxd.jpg :D OH.. and by the way, yes panel lines are now being added to the fuselage (nose) area, I promise, it will be detailed. Similar to TOS but like an advanced version as it is. :D |
Quote:
Send me the PM and I'll give you a call. Nice to see you around again. Its been a while. Sandy |
So, is it done yet? Is it done yet? :D
|
WC for BS2001 (LOL... BS - pun intended!)
Hi Jeffrey,
This is Terri posting for Michael. He's working on the last wing and said we will cast the wings and vertical stabilizer very soon, like in a few minutes! I'm going to help make the mold (multitasking while doing laundry!) Like most projects, this is taking longer than expected. I think Michael is usually too optimistic when he talks about how long something will take for him to finish because he truly enjoys it so much that he doesn't realize how much time is passing! Gotta run downstairs and add fabric softener and then will make a mold I hope! Terri WC :salute: |
Hello all. Terri is downstairs in the process of making the mold for the left wing. 1st casting should be revealed in a few hours. ;)
|
Photos.....Molds in the making tonight and they are really well done. All visible falws in parts have been brought up to near perfection for smoothness and sharp detail. Terri really assited in the clay build up of the left wing and assisted in perfect measuring... :D she's a chemist and stuff! ;)
The molds are being formed and here are silly pics of such. Think I'll do the next wing standing in mold box instead of flat, give your opinion of whih you think would be best. ;) http://tinypic.com/hw048n.jpg http://tinypic.com/hw03u0.jpg will present pics of molded components later tonight. :salute: |
This is fun!
I feel a little bit better now about being able to actually contribute to something! This is our first time to make a mold and since the supplies were so expensive, I was worried about wasting even a drop! It's great to get that "first time" over with so that we now know what to expect. I estimated how much we'd need by calculating the volume of the box itself. The actual piece being molded is just a wing, so I ignored its displacement of volume for the sake of being conservative. My estimates told me that we'd have barely enough mixture to do the vertical stabilizer mold. After Michael poured it in there was a little bit left. Then I remembered that he had made a little box of greeblies to mold, so I ran and got it and he filled it up. Even if the greeblie box hadn't been ready, Michael would have had time to make one because there's a 30 minute working time for the molding material.
Next we'll do the actual casting of the parts and I'm a little nervous about it working out. The work time after mixing the liquids together is very short. Again, I don't want to waste any because the stuff is so expensive (even after getting it at 40% off.) I do expect the casting to be easier than the acutal making of the mold. Michael will post pictures of the casted vertical stabilizer, hopefully later tonight! ;) |
I's sure like to see an article on how to do this type of modeling... *notes that the Articles section of the site is rather... empty*
|
Quote:
|
Molded Master Parts to be further refined for the sharpest detail we can achieve.
Terri did a great job, and learned alot about (pot life) :D This is going to be a great kit, and original. Keeping TOS dream alive and well. And yes, the sprue and any flash will definately not be there when you get you kit. :D http://tinypic.com/hwctig.jpg http://tinypic.com/hwctpl.jpg :salute: |
Here is a pic of the (final) canopy shape. Am building it now at 12:55 a.m.
This is cool I'm happy with it after making about 5 before coming to this. :salute: http://tinypic.com/hwehk5.jpg |
Um.... yeah
Quote:
Last night I ordered supplies in bulk and the new stuff has a longer pot life. I think it's around 5-7 minutes. Of course the set-up time takes hours rather than minutes, but that's a sacrifice we're willing to make. I also believe that with a longer set-up time more bubbles can escape before it sets. :nervous: |
Something you can do to extend your pot-life is to actually chill one half of the resin in the refrigerator. The big trouble with this is the condensation caused by the warm-up inside the container when you take it out. urethanes DO NOT LIKE moisture. Atmospheric moisture is what causes most resins to go bad after a while. ALSO: Have you been privvy to my article concerning urthane resins? If you haven't I will post the text here. Urethanes are your friend as long as you respect them. But if you don't, you WILL get ill.
-Gordon |
Quote:
|
Here's the low-down: Urethane, when it cures, releases Isocyanate gasses. Sound familiar? That's because the root word is Cyanaide... poison.
Isocyanates are long-term poisons that build up in your system. Your body will try very hard to get rid of them, but they don't like to go easily. Exposure to them (even regulated exposure) wil eventually cause them to build up in your body and make you ill. The amount that it takes varies from person to person, and the time it takes to build up in your body varies as well. But over time, you WILL develop a sensitivity to them. Typical symptoms include: shortness of breath (induced athsma), skin rashes, itching, throat irritation, dizziness, and oddly enough, back pain. Other, less obvious effects are irritability, short temper, and even paranoia. But like I mentioned, this all varies from person to person. Example: My boss Dave got a massive exposure to urethane several years ago. He can no longer be in the building when we pour resins or he immediately goes into athsmatic arrest. I have been exposed over the course of 12 years. I get skin rashes, back pains, and athsmatic attacks when I'm exposed. But my boss Mike can work with the stuff unprotected after 12 years and has no obvious effects. On the extreme end, I personally had a friend who committed suicide after long-term chronic exposure. First he tried to commit suicide by police officer. Eventually he just did it himself. His diaries indicated a long-term paranoia that coincided almost perfectly with his unprotected exposure to urethane. Did he have other problems? Yes. But I sincerely believe that the situation was spurred on by chemical influence. So, how to avoid all this? Easy: 1) get yourself a NIOSH approved filter mask with the biggest, most ass-kicking filter cartridges you can buy. Make sure your catridges are the highest rated ones you can get. They won't completely protect you, but they will help limit the exposure through your lungs. 2) set up your workspace so that you are cross-ventilating to the OUTDOORS. This means you need to have a CONSTANT flow of air running through your space. Clean air must enter at one end and fume-y air must be vented out the other end. Be sure you don't vent right into an area that supplies air to another house or building. Your fumes will just get sucked up and deposited into their space. 3) always wear latex (or if you're allegic to latex) nitrile gloves when handling the urethane components or the mixed combo. Not only can Isocyanates enter your body through the lungs as fumes, but they also affect you through the skin. Be sure to get yourself some of those disposable tyvec jumpsuits they use when they paint cars. It'll keep you from wrecking your clothing. 4) Use and Do all the stuff above. Also: DO NOT do this IN YOUR HOUSE. There is a reason why these things are called "garage kits" by hobbyists. Its getting to the cold seasons of the year, so I suggest you make a spot in your garage and set up space-heaters to keep the place warm. PLEASE... I'm BEGGING YOU. DON'T DO THIS IN YOUR BASEMENT OR HOUSE. 5) If you feel like you've started to show any of the signs of overexposure, you need to get away from the stuff. Take a break from it for at least two weeks. In the mean time, you can exercise and pump your lungs good and hard...run, bike, whatever. Drink ALOT of water. It helps your body get rid of the toxins. And best of all, get thee to a sauna. Especially after you workout. A sauna will force you to sweat alot and encourage your body to expell the toxins that way. Now, about your resin. If you weren't given a MSDS (Material Safety Data Sheet) when you bought it, you should go back there and get one. Every chemical available to the populace MUST have an accompanying MSDS. It is the law. Read the MSDS carefully and it will probably tell you the make-up of your paint system. If you have any questions at all, just pick up the phone and call the manufacturer. They will be happy to answer your questions about the specific product. Last but not least: Don't think you're invulnerable because it doesn't affect you right away. Use the protection from the start and you WILL stay healthy. -Gordon |
All times are GMT -7. The time now is 08:03 PM. |
Powered by: vBulletin Version 3.8.11, Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Content and Graphics ©2000-Present Colonial Fleets